ASN logo
ASN Wikibase Occurrence # 30338
Last updated: 29 September 2020
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information. If you feel this information is incomplete or incorrect, you can submit corrected information.

Type:Silhouette image of generic B212 model; specific model in this crash may look slightly different
Bell 212
Owner/operator:Houston Helicopters, Inc.
Registration: N8144M
C/n / msn: 30706
Fatalities:Fatalities: 2 / Occupants: 2
Other fatalities:0
Aircraft damage: Written off (damaged beyond repair)
Location:Near Philadelphia, MS -   United States of America
Phase: En route
Departure airport:Tuscaloosa, AL (TCL)
Destination airport:Jackson, MS (JAN)
Investigating agency: NTSB
At the last refueling stop the pilot and passenger stated to the lineman that the greenhouse window above the pilot had cracked during the previous leg of the flight. The transcript of communications recorded on the cockpit voice recorder showed that about 29 minutes before the accident, the passenger stated to the pilot "I think if I hadn't-a broke that off we wouldn't had any greenhouse by the time we got home". About 18 minutes before the accident, the passenger stated to the pilot "boy those catfish are going crazy down there aren't they". The pilot respond "yep", "must have been the vibrations from the helicopter". About 2 minutes later the passenger and pilot discuss sighting deer in a field. About 1 minute 30 seconds before the accident, the pilot asked the passenger "has this vertical just gotten in here or has it been here for a while?" The passenger replied "we haven't had any verticals at all." The pilot replied, "we do now." The passenger replied, "yeah well it started right after we left back there. I think it maybe ah that's why I was thinking it was the air." About 20 seconds later, the passenger stated that another person had tracked the helicopter's blades before they left and that he was commenting on how smooth it was. About 40 seconds later the pilot stated "this stuff is getting worse." The recording then ended. Witnesses in the area of the accident site stated that they observed the helicopter flying from east to west, just above the treetops. The helicopter began rolling back and forth. They then observed the main rotor blades contact the tail area, and the aft tail boom and tail rotor separate. Shortly after this, the main rotor separated and the helicopter descended and crashed to the ground. A fire erupted during ground impact. Witnesses did not observe any smoke come from the helicopter prior to the accident. The entire main rotor system was accounted for in the wreckage, except for the pitch change horn for the "red" main rotor blade and the majority of the pitch change link that attaches to the "red" pitch change horn at the pitch change links lower rod end. The "red" grip remained in place in the main rotor system. The surface of the "red" grip exhibited two boreholes that mated with two bushing that were part of the departed and missing "red" pitch change horn. The mating grip surface exhibited a blackish residue near the pitch change horn boreholes, and the blackish area extended beyond the boreholes. The crashsite and an extended area back-up the wreckage path were searched extensively, including by Boy Scout parties; the "red" pitch change horn and most of the "red" pitch change link were not found. Examination of the red grip by an NTSB metallurgist showed the surfaces of both the upper and lower holes showed extensive areas of dark deposits and surface damage consistent with repeated small relative movements against mating objects (fretting). Visible fretting areas covered most of the surface of the bushing counter bores and portions of the fractured surfaces of the threads. Energy dispersive x-ray analysis of samples of the black deposits taken from the upper hole found them to mostly contain aluminum and iron and significant amounts of oxygen along with minor amounts for the other constituents of the grip and bushing. Samples from the lower hole were found to be mostly aluminum with large peaks for iron, cadmium, silicon and oxygen. Both bushing counter bores showed localized material removal and enlargement of the diameters. Up to .020 to 0.025 inches of material were removed in localized areas from the bushing bore. In addition, the bores were deformed and distorted adjacent to the grip surface. The surfaces of the holes, particularly the upper one, also contained circumferential marks in the bushing counter bore, the lock ring diameter and on the fractured threads indicating progressive and incremental movement of the mating objects. No other evidence of failure or malfunction of the helicopter structure, flight controls, engine, or rotor and rotor drive system was found.

Probable Cause: The failure of the pilot and company maintenance personnel during preflight and periodic inspections to identify the signs of fretting and looseness in the "red" main rotor blade pitch change horn to main rotor blade grip attachment, resulting in the helicopter continuing in service with a loose pitch change horn, separation of the pitch change horn from the blade grip, and inflight breakup of the helicopter due to the main rotor striking the tailboom. Contributing to the accident was the pilot's failure to respond to increased vibration in the main rotor system and land immediately.



Revision history:

27-Sep-2008 01:00 ASN archive Added
14-May-2010 22:51 JINX Updated [Location, Country, Source, Damage, Narrative]
22-Jun-2013 13:39 JINX Updated [Time, Operator, Total fatalities, Total occupants, Other fatalities, Location, Phase, Nature, Departure airport, Destination airport, Source, Narrative]
14-Dec-2017 09:47 ASN Update Bot Updated [Time, Operator, Departure airport, Destination airport, Source, Narrative]

Corrections or additions? ... Edit this accident description