ASN Wikibase Occurrence # 122819
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can
submit corrected information.
Date: | Friday 27 May 2011 |
Time: | 18:00 |
Type: | Bell OH-58A-BF Kiowa |
Owner/operator: | Bay Co Sheriff's Office |
Registration: | N82772 |
MSN: | 40043 |
Year of manufacture: | 1968 |
Total airframe hrs: | 4725 hours |
Engine model: | Allison T63-A-720 |
Fatalities: | Fatalities: 0 / Occupants: 2 |
Aircraft damage: | Substantial |
Category: | Accident |
Location: | Old Panama City Airport, FL -
United States of America
|
Phase: | Take off |
Nature: | Unknown |
Departure airport: | Panama City, FL (KPFN) |
Destination airport: | Panama City, FL (KPFN) |
Investigating agency: | NTSB |
Confidence Rating: | Accident investigation report completed and information captured |
Narrative:The pilot was hover taxiing the helicopter straight out of an old, temporary hangar, as he had done numerous times. He estimated that the helicopter was about 3 feet above the ground, the last few feet of the tail were still inside the hangar, and he heard a loud bang. He started to lower the collective, but could not control the helicopter, which tipped over on its left side as it impacted the ground. Photographs showed that the main rotor blades had separated from the mast. The vertical tail fin had scrape marks on its top and the upper leading edge had an almost horizontal line several inches below the top. The tail rotor blades, which did not extend above the top of the vertical fin, were pristine. The hangar door overhead frame had three sets of scrape marks, with one angled about 30 degrees to the right and two sets angled about 20 to 25 degrees to the left. Electrical conduit would have normally been secured above the hangar door frame, but was drooped below it, separated and coiled. Remnants of the conduit, and the fact that the main rotor blade tips would have rotated above the vertical tail fin, indicate that the conduit likely had drooped below the hangar frame after the main rotor passage, then snagged the top of the vertical fin. The multiple sets of scrape marks at different angles on the underside of the overhead hangar frame indicate that the helicopter then likely pivoted several times while snagged, as the pilot lost control. No preexisting mechanical malfunctions were noted with the helicopter.
Probable Cause: The drooping electrical conduit, which snagged the vertical fin and resulted in the pilot's inability to control the helicopter. Contributing to the accident was the operator's decision to have the pilot fly the helicopter out of the hangar.
Accident investigation:
|
| |
Investigating agency: | NTSB |
Report number: | ERA11TA317 |
Status: | Investigation completed |
Duration: | 8 months |
Download report: | Final report |
|
Sources:
NTSB
Location
Revision history:
Date/time | Contributor | Updates |
29-May-2011 03:34 |
gerard57 |
Added |
29-May-2011 05:04 |
RobertMB |
Updated [Time, Aircraft type, Location, Departure airport, Source] |
30-May-2011 04:06 |
RobertMB |
Updated [Operator] |
31-May-2011 17:40 |
RobertMB |
Updated [Aircraft type, Registration, Cn] |
21-Dec-2016 19:25 |
ASN Update Bot |
Updated [Time, Damage, Category, Investigating agency] |
27-Nov-2017 16:54 |
ASN Update Bot |
Updated [Cn, Other fatalities, Nature, Departure airport, Destination airport, Source, Narrative] |
30-May-2023 00:15 |
Ron Averes |
Updated [[Cn, Other fatalities, Nature, Departure airport, Destination airport, Source, Narrative]] |
The Aviation Safety Network is an exclusive service provided by:
CONNECT WITH US:
©2024 Flight Safety Foundation