ASN Wikibase Occurrence # 163473
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can submit corrected information.
| Date: | Tuesday 21 January 2014 |
| Time: | 15:37 |
| Type: |  Bell 47D-1 |
| Owner/operator: | Milam Inc |
| Registration: | N93067 |
| MSN: | 5501 |
| Year of manufacture: | 1965 |
| Total airframe hrs: | 3980 hours |
| Engine model: | Franklin 6V-350-A |
| Fatalities: | Fatalities: 0 / Occupants: 2 |
| Aircraft damage: | Substantial |
| Category: | Accident |
| Location: | Pell City, AL -
 United States of America
|
| Phase: | Landing |
| Nature: | Executive |
| Departure airport: | Birmingham, AL (BHM) |
| Pell City, AL (None) | |
| Investigating agency: | NTSB |
| Confidence Rating: |  Accident investigation report completed and information captured |
The commercial pilot was completing a business flight in the helicopter. He reported that, while descending the helicopter for a confined off-airport landing, at 25 to 35 ft above ground level, he heard a “snap/pop” and that the engine suddenly began “over-revving.” The helicopter started descending and then touched down hard, and one of the main rotor blades struck the helicopter’s tail. After touchdown, the engine was still running, but the rotor blades were not moving.
Examination of the transmission revealed that it incorporated a light-weight clutch assembly, which was not authorized for use in the installed transmission model. Further examination revealed that the clutch shoe running surface on the inner diameter of the clutch drum exhibited a series of abnormal wear grooves along the entire surface of clutch shoe contact and that the clutch lining of each shoe exhibited glazing, which occurs when the clutch is improperly engaged. The contact surface of each clutch shoe also contained numerous metallic slivers that were atypical of a normal in-service clutch assembly and appeared to be material that had transferred from the drum to the shoes.
During the transmission examination, the pilot was asked to describe his normal engine start and clutch engagement procedure. The clutch engagement procedure described by the pilot was not in accordance with the published procedure. The pilot’s procedure likely resulted in a lengthy clutch engagement and an extended period of clutch slippage during each start that led to the glazed condition of the clutch assembly. Once the glazed condition began to develop, the period of clutch slippage during each start lengthened, further contributing to the glazed condition. Ultimately, the glazed condition resulted in the in-flight disengagement of the clutch and a loss of rotor rpm.
The pilot reported that, about 15 flight hours before the accident, he had a mechanic install an engine in the helicopter that produced 25 more horsepower than the previously installed engine. The installation of the higher horsepower engine would have increased the tendency for slippage of a glazed clutch assembly.
The pilot also reported that the transmission had accumulated about 615 hours since overhaul. According to the helicopter’s maintenance and overhaul instructions, the transmission should be disassembled every 600 hours to inspect all parts, including the clutch, for damage or excessive wear. Given that the engine had been installed about 15 flight hours before the accident, the 600-hour inspection could have been accomplished at that time. However, review of maintenance records did not indicate that the 600-hour transmission inspection had occurred, and the mechanic who installed the higher horsepower engine reported that he did not disassemble the transmission.
Probable Cause: The pilot’s use of an improper clutch engagement procedure, which resulted in clutch glazing, slippage, and, ultimately, the in-flight disengagement of the clutch and a loss of rotor rpm. Contributing to the accident were the installation of a light-weight clutch assembly and a higher horsepower engine, both of which increased the tendency for clutch slippage, and inadequate inspection of the clutch assembly.
Accident investigation:
 |
|
Sources:
NTSB
History of this aircraft
Other occurrences involving this aircraft
| 27 January 1992 | N93067 | Avico, Inc. | 0 | Cross City, FL | |
sub |
Location
Revision history:
| Date/time | Contributor | Updates |
|---|---|---|
| 23-Jan-2014 08:03 | Geno | Added |
| 23-Jan-2014 08:08 | Geno | Updated [Source] |
| 28-Jan-2014 06:43 | Geno | Updated [Time, Aircraft type, Operator, Nature, Departure airport, Destination airport, Source, Narrative] |
| 21-Dec-2016 19:28 | ASN Update Bot | Updated [Time, Damage, Category, Investigating agency] |
| 29-Nov-2017 13:22 | ASN Update Bot | Updated [Other fatalities, Nature, Departure airport, Destination airport, Source, Narrative] |
Corrections or additions? ... Edit this accident description
The Aviation Safety Network is an exclusive service provided by:
Quick Links:
| ASN Home | Send Correction / Feedback |
| FSF Home | Disclaimer | Copyright |
| Contact Us | Privacy Policy |
| Press / Media |
CONNECT WITH US:
©2024 Flight Safety Foundation