ASN Wikibase Occurrence # 830
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can
submit corrected information.
Date: | Tuesday 4 December 2007 |
Time: | 10:50 |
Type: | Robinson R22 Beta |
Owner/operator: | Razor Blades |
Registration: | N70035 |
MSN: | 3641 |
Year of manufacture: | 2004 |
Total airframe hrs: | 1332 hours |
Fatalities: | Fatalities: 0 / Occupants: 1 |
Aircraft damage: | Substantial |
Category: | Accident |
Location: | Gainesville, Florida -
United States of America
|
Phase: | En route |
Nature: | Training |
Departure airport: | St. Petersburg, FL (PIE) |
Destination airport: | Gainesville, FL (GNV) |
Investigating agency: | NTSB |
Confidence Rating: | Accident investigation report completed and information captured |
Narrative:The pilot of the helicopter was under flight instruction to add a rotorcraft rating to his certificate and was on a solo cross-country flight. The helicopter had been in cruise flight for about 1 hour and 20 minutes when the pilot noticed an intermittent illumination of the "clutch light" and perceived a loss of altitude. The pilot "reset the circuit breaker" and increased collective to regain the lost altitude. He then perceived a loss of rotor rpm and slowly and continuously lowered the collective to maintain the rotor rpm in the normal operating range. When the helicopter reached approximately 150 feet above ground level, the pilot could no longer maintain rotor rpm and entered autorotation. During the descent, he selected an empty parking lot for a landing, where the helicopter landed hard, bounced, and then rolled over onto its side. He added that the engine was running before and after ground contact, and he did not report any deficiencies in the handling characteristics of the helicopter. Functional testing of the clutch assembly revealed that the rigging and operation of the assembly were within factory specifications, but the engagement cycle time exceeded the factory limit. The pilot stated that he "reset" the circuit breaker, and continued to adjust the collective pitch to regain altitude and rotor rpm. The emergency procedure listed in the Pilot's Operating Handbook directed the pilot to "pull" the clutch circuit breaker and land immediately.
Probable Cause: The pilot's failure to follow the published emergency procedure. Contributing to the accident was a malfunction of the clutch assembly.
Accident investigation:
|
| |
Investigating agency: | NTSB |
Report number: | NYC08LA052 |
Status: | Investigation completed |
Duration: | |
Download report: | Final report |
|
Sources:
NTSB:
https://www.ntsb.gov/_layouts/ntsb.aviation/brief.aspx?ev_id=20071228X02002&key=1 FAA register: 2. FAA:
http://registry.faa.gov/aircraftinquiry/NNum_Results.aspx?NNumbertxt=70035 Location
Revision history:
Date/time | Contributor | Updates |
23-Jan-2008 04:23 |
JINX |
Added |
29-Sep-2016 22:01 |
Dr.John Smith |
Updated [Time, Location, Departure airport, Destination airport, Source, Narrative] |
21-Dec-2016 19:13 |
ASN Update Bot |
Updated [Time, Damage, Category, Investigating agency] |
21-Dec-2016 19:14 |
ASN Update Bot |
Updated [Time, Damage, Category, Investigating agency] |
21-Dec-2016 19:16 |
ASN Update Bot |
Updated [Time, Damage, Category, Investigating agency] |
21-Dec-2016 19:20 |
ASN Update Bot |
Updated [Time, Damage, Category, Investigating agency] |
04-Dec-2017 19:03 |
ASN Update Bot |
Updated [Operator, Other fatalities, Nature, Departure airport, Destination airport, Source, Narrative] |
The Aviation Safety Network is an exclusive service provided by:
CONNECT WITH US:
©2024 Flight Safety Foundation